Divide by 2 clock in VHDL

Clock dividers are ubiquitous circuits used in every digital design. A divide-by-N divider produces a clock that is N times lesser frequency as compared to input clock. A flip-flop with its inverted output fed back to its input serves as a divide-by-2 circuit. Figure 1 shows the schematic representation for the same.

Divide by 2 clock circuit

                                          

Following is the code for a divide-by-2 circuit.

-- This module is for a basic divide by 2 in VHDL.

library ieee;

use ieee.std_logic_1164.all;

entity div2 is

                port (

                                reset : in std_logic;

                                clk_in : in std_logic;

                                clk_out : out std_logic

                );

end div2;

-- Architecture definition for divide by 2 circuit

architecture behavior of div2 is
signal clk_state : std_logic;

begin

                process (clk_in,reset)

                begin

                                if reset = '1' then

                                                clk_state <= '0';

                                elsif clk_in'event and clk_in = '1' then

                                                clk_state <= not clk_state;

                                end if;

                end process;
clk_out <= clk_state;

end architecture;

Hope you’ve found this post useful. Let us know what you think in the comments.

Latency and throughput – the two measures of system performance

Performance of the system is one of the most stringent criteria for its success. While performance increases the desirability among customers, cost is what makes it affordable. This is the reason why system designers aim for maximum performance with available resources such as power and area constraints. There are two related parameters that determine the performance output of a system –

Throughput - Throughput is a measure of the productivity of the system. In electronic/communication systems, throughput refers to rate at which output data is produced. Higher the throughput, more productive is the system. In most of the cases, it is measured as time difference between two consecutive outputs (nth and n+1th). Throughput also refers to the rate at which input data can be applied to system.

Let us discuss with the help of an example:

Above figure depicts the throughput of 3 number adder. Result of input set applied at 1st clock cycle appears at output at 3rd clock cycle and in 4th clock cycle next input set is applied and output comes in 6th clock cycle.  Hence, throughput of above design is ⅓ per clock cycle. As we can see from diagram, first input is applied in first clock cycle and 2nd input is applied in 4th clock cycle. Hence we can also say that throughput is rate at which input data can be applied to system.

Latency- Latency is the time taken by a system to produce output after input is applied. It is a measure of delay response of a design. Higher the latency value, slower is the system. in synchronous designs, it is measured in terms of number of clock cycles. In combinational designs, latency is basically propagation delay of circuit. In non pipelined designs, latency improvement is major area of concern. In more general terms, it is time difference between output and input time.

Relationship between throughput and latency: Both latency and throughput are inter-related. It is desired to have maximum throughput and minimum latency. Increasing latency and/or throughput might make the system costly. Let us take an example. Consider a park with 3 rides and it takes 5 minutes for a ride.  A child can take sequentially these rides; i.e, ride 1, ride 2 and then ride 3. Firstly, let us assume that only one child at a time is allowed to enter park at a time. While he is taking a ride, no one is allowed to enter the park. Thus, the throughput of the park is 15 minutes per child and latency is 15 minutes. Now, let us assume that while a child has finished taking ride1, another child is allowed to enter park. Thus, in this case, throughput will be 5 minutes per child whereas latency is still 15 minutes. Thus, we have increased the throughput of the system without affecting latency and at the same cost.