Showing posts with label TG gates. Show all posts
Showing posts with label TG gates. Show all posts

Transmission Gates


Transmission gates represent another class of logic circuits, which use Transmission gates as basic building block. A transmission gate consist of a PMOS and NMOS connected in parallel. Gate voltage applied to these gates is complementary of each other (C and Cbar shown in figure 1). Transmission gates act as bidirectional switch between two nodes A and B controlled by signal C. Gate of NMOS is connected to C and gate of PMOS is connected to Cbar(invert of C). When control signal C is high i.e. VDD, both transistor are on and provides a low resistance path between A and B. On the other hand, when C is low, both transistors are turned off and provide high impedance path between A and B.

A transmission gate consists of a PMOS and an NMOS in parallel.
Figure 1: Transmission gate
A detailed analysis of working of transmission gates follows:
When input node A is connected to VDD and control logic C is also high, C = 1 : The output node B may be connected to capacitor. Let us say, voltage at output node is Vout.
For PMOS, Source of is at higher voltage than drain.
For NMOS, drain is at higher voltage than Source terminal.
 Hence, node A will act as source terminal for pMOS and as drain terminal for nMOS.
Drain to Source and gate to source voltages for nMOS are as :
                                                       VDS,n = VDD – Vout
                                                       VGS,n = VDD – Vout
For nMOS to be turned off, VGS,n < Vth,n
                                             VDD – Vout < Vth,n
                                             Vout > VDD – Vth,n (Cut off region)
For Vout < VDD – Vth,n
VDS,n > VGS,n – Vth,n
i.e. will operate in saturation mode

Similarly for pMOS,
VDS,p = Vout - VDD
VGS,p = – VDD

For pMOS to be turned off VGS,p > vth,p threshold voltage for pMOS is –ve so pMOS will always be turned on.

For pMOS to operate in linear region, VDS > VGS – vth,p
Vout – VDD > -VDD – Vth,p
Vout > - Vth,p
Vout > |Vth,p|

For Vout ≤ |Vth,p|, pMOS will be in saturation mode.

Unlike nMOS, pMOS remain turned on regardless of output voltage Vout


Thus PMOS will always be turned on, and as we know that PMOS Passes a strong 1 so voltage level high will be transmitted unattenuated.

Similarly,
When voltage at node A,Vin = 0 and C = VDD, node A will act as source terminal for nMOS and will act as drain for pMOS. nMOS will always be turned on hence level 0 will also be transmitted unattenuated.


when voltage at node A,Vin = VDD and C = 0 node A will act as drain terminal for nMOS and source terminal for pMOS
VGS,n = 0 – VDD < Vth,n (cut off region)

Hence nMOS will be turned off
VGS,p = VDD – VDD = 0 > Vth,p (Cut off region)

Thus both transistor will remain off. Path between A and B will be an open circuit.

when voltage at node A,Vin = 0 and C = 0 : node A will act as source terminal for nMOS and will act as drain for pMOS.
VGS,n = 0 – 0 = 0 <Vth,n (Cut off region)
VGS,p = VDD – Vout

VGS,p will be some positive voltage and threshold voltage of pMOS ,Vth,p is negative.
VGS,p > Vth,p (Cut off region)

Hence both transistor will remain off and high impedance path exists between A and B.