What is the difference between a normal buffer and clock buffer?

A buffer is an element which produces an output signal, which is of the same value as the input signal. We can also refer a buffer as a repeater which repeats the signal it is receiving, just as there are repeaters in telephone signal transmission lines. You must have noticed that we have two kinds of buffers (or any logic gate) available in standard cell libraries as:

• Clock buffer: The clock buffers are designed specifically to have specific properties that are supposed to be good for clock distribution networks (clock trees). The specific properties that are required in an ideal clock tree buffer are given as below. However, it is not possible to attain these ideal properties for every buffer at every technology node. It may be only possible to get close to these properties.
• Equal rise and fall times
• Less delays
• Less delay variations with PVT and OCV

• Normal buffer/data buffer: For a data buffer, the above properties are usually less desired

Usually, we can say that following differences may exist between a clock buffer and a normal buffer:

• In SoCs, clock routing is done in higher metal layers as compared to signal routing. So, to provide easier access to clock pins from these layers, clock buffers may have pins in higher metal layers. That is, vias are provided in standard cell itself instead of necessitating on having in clock distribution network. For a data buffer, the pins are expected to be in lower layers only.
• Clock buffers are balanced. In other words, rise and fall times of clock buffers are nearly equal. The reason behind this is that if the clock buffers are not balanced, there will be duty cycle distortion in the clock tree, which can lead to pulse width violations as discussed in minimum pulse width violation example. On the other hand, data buffers can compromise with either of rise/fall times. In other words, they dont need to have PMOS/NMOS size to be 2:1; and hence, can be of smaller size as compared to clock buffers.
• Due to above reason, clock buffers consume more power as compared to normal buffers.
• Generally, you will find clock buffers with higher drive strength as compared to normal buffers. So that a clock buffer can drive long nets and can have higher fanouts. This helps clock buffers, and hence, clock trees to have less overall delays.

Read next: Clock skew

Performance gain with latches

The property of latches being transparent gives them a basic characteristic, known as time borrowing, owing to which they can capture data over a period of time rather than an instant. Using this property of latches intelligently can result in performance advantage for specific design scenarios, especially for designs having asymmetric data paths in subsequent stages. Let us elaborate with the help of an example.

Let us suppose a design having two stages of pipeline with combinational logic in each stage as 12 ns and 5 ns respectively as shown in figure 1 below:

Figure 1: 2-stage pipelining

If we assume clock period to be 16 ns (half cycle being 8 ns), then each latch stage will borrow time from the subsequent stage as shown in figure below:

.

Now, since all the registers get the same clock signal, the minimu clock period is the maximum of combinational delays from REGA to REGB and REGB to REGC.

T_clk > MAX (T_{combregA->regB}, T_{combr(regB->regC)})

Thus, this circuit cannot run with half clock period less than 12 ns, or clock period less than 24 ns.

This situation can be easened up if we replace REGB with a negative level-sensitive latch. Let us have a look at figure 2 below. Although the number of stages still remains the same, LATB can borrow time from next stage without impacting any logic.

Figure 2: Latch replacing register in the 2-stage pipelining

The same is shown in figure 3 below with the help of waveform. The clock is having a period of 9 ns. The latch can borrow time of 3 ns from next stage, still meeting the setup time by 1 ns. Thus, we have succeeded in reducing the half time period from 12 ns to 9 ns (time period from 24 ns to 18 ns), just by changing the register to a latch. This is how a latch can help gain in performance.

If there are multiple latch stages in series, each can borrow from the subsequent stage such that overall timing is met. For example, figure 3 shows 6 latches in series.